MIkrotik Academy for Network knowledge share: 2019

following configuration collected from other blogs.

This blog introduces Link Aggregation Control Protocol (LACP) bonding and provides step-by-step configuration of LACP bonding on Red Hat Enterprise Linux (RHEL) and CentOS operating systems versions 6 and 7.

Introduction

Network bonding enables the combination of two or more network interfaces into a single-bonded (logical) interface, which increases the bandwidth and provides redundancy. If a specific network interface card (NIC) experiences a problem, communications are not affected significantly as long as the other slave NICs remain active.

Bonding modes supported by RHEL and CentOS operating systems

The behavior of the bonded interfaces depends on the mode that is selected. RHEL supports the following common bonding modes:

Mode 0 (balance-rr): This mode is also known as round-robin mode. Packets are sequentially transmitted and received through each interface one by one. This mode provides load balancing functionality.
Mode 1 (active-backup): This mode has only one interface set to active, while all other interfaces are in the backup state. If the active interface fails, a backup interface replaces it as the only active interface in the bond. The media access control (MAC) address of the bond interface in mode 1 is visible on only one port (the network adapter), which prevents confusion for the switch. Mode 1 provides fault tolerance.
Mode 2 (balance-xor): The source MAC address uses exclusive or (XOR) logic with the destination MAC address. This calculation ensures that the same slave interface is selected for each destination MAC address. Mode 2 provides fault tolerance and load balancing.
Mode 3 (broadcast): All transmissions are sent to all the slaves. This mode provides fault tolerance.
Mode 4 (802.3ad): This mode creates aggregation groups that share the same speed and duplex settings, and it requires a switch that supports an IEEE 802.3ad dynamic link. Mode 4 uses all interfaces in the active aggregation group. For example, you can aggregate three 1 GB per second (GBPS) ports into a 3 GBPS trunk port. This is equivalent to having one interface with 3 GBPS speed. It provides fault tolerance and load balancing.
Mode 5 (balance-tlb): This mode ensures that the outgoing traffic distribution is set according to the load on each interface and that the current interface receives all the incoming traffic. If the assigned interface fails to receive traffic, another interface is assigned to the receiving role. It provides fault tolerance and load balancing.
Mode 6 (balance-alb): This mode is supported only in x86 environments. The receiving packets are load balanced through Address Resolution Protocol (ARP) negotiation. This mode provides fault tolerance and load balancing.

IEEE 802.3ad Link Aggregation Policy and LACP

Before we explore LACP configuration, we should understand the IEEE 802.3ad link aggregation policy and LACP bonding, which allows us to aggregate multiple ports into a single group. This process combines the bandwidth into a single connection.

IEEE 802.3ad link aggregation enables us to group Ethernet interfaces at the physical layer to form a single link layer interface, also known as a link aggregation group (LAG) or bundle.

Some users require more bandwidth in their network than a single fast Ethernet link can provide. Using IEEE 802.3ad link aggregation in this situation provides increased port density and bandwidth at a lower cost.

For example, if you need 2 GBPS bandwidth to transmit data and have only 1 GBPS Fast Ethernet links installed on your system, creating a LAG bundle containing two 1 GBPS Fast Ethernet links is more cost-effective than purchasing a single 2 GBPS Ethernet link.

The following diagram illustrates the IEEE 802.3ad link aggregation policy:

LACP is a mechanism for exchanging port and system information to create and maintain LAG bundles. The LAG bundle distributes MAC clients across the link layer interface and collects traffic from the links to present to the MAC clients of the LAG bundle.

LACP identifies the MAC address of the Ethernet link that has the highest port priority and is of the lowest value, and it assigns that MAC address to the LAG bundle.

This bonding mode requires a switch that supports IEEE 802.3ad dynamic links.

Steps to configure LACP bonding

Preparation: Collect the required details to configure bonding. We recently implemented on production servers the scenario shown in the following table. We changed the IP address, MAC, and UUID details to maintain security.

Bond interface	bond1
Bonding type	802.3ad
Bonding options	miimon=100,lacp_rate=fast,xmit_hash_policy=layer2+3
Slave interfaces	p5p1 p5p2
MTU	9000
IP address/prefix	179.254.0.2/16

The following sections show the steps to configure LACP bonding by using the command line interface (cli) and the NetworkManager command line interface (nmcli) tools.

STEPS TO CONFIGURE LACP BONDING ON RHEL OR CENTOS 6 BY USING THE CLI TOOL

Backup the existing interfaces before you configure the bonding. Bring $slave1 and $slave2 down and move these files to a backup directory by using the following commands:
```
~]# ifdown p5p1 ; ifdown p5p2
~]#cd /etc/sysconfig/network-scripts
~]#mv -v ifcfg-p5p1 ifcfg-p5p2 ~/BACKUPDIR
```
Make sure module bonding is loaded by using the following command. You can also load the module with the command #modprobe bonding.
```
~]# lsmod |grep -i bonding
bonding               145728  0
```

Create the file ifcfg-bond1 and modify the configuration by using the following commands:

~]#cd /etc/sysconfig/network-scripts
~]#cat ifcfg-bond1
DEVICE=bond1
TYPE=Ethernet
ONBOOT=yes
USERCTL=no
NM_CONTROLLED=no
MTU=9000
BOOTPROTO=static
IPADDR=179.254.0.2
PREFIX=16
DNS1=<DNS_IP>
BONDING_OPTS="mode=802.3ad miimon=100 lacp_rate=fast xmit_hash_policy=layer2+3"

Modify the slave interface (slave1 and slave2) configurations by using the following commands:

~]#cat ifcfg-p5p1
DEVICE=p5p1
BOOTPROTO=none
ONBOOT=yes
SLAVE=yes
USERCTL=no
NM_CONTROLLED=no
MASTER=bond1

~]#cat ifcfg-p5p2
DEVICE=p5p2
BOOTPROTO=none
ONBOOT=yes
SLAVE=yes
USERCTL=no
NM_CONTROLLED=no
MASTER=bond1

Restart the network or restart the server by using one of the following commands:
```
~]# service network restart

or

~]# init 6
```

After the service or server restart, check the proc for a bond interface by using the following command:

~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
Active Aggregator Info:
  Aggregator ID: 1
  Number of ports: 1
  Actor Key: 9
  Partner Key: 550
  Partner Mac Address: 00:24:04:ef:bc:76

Slave Interface: p5p1
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: b4:b5:3f:8d:53:77
Aggregator ID: 1
Slave queue ID: 0

Slave Interface: p5p2
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: b4:b4:2f:5e:55:7b
Aggregator ID: 2
Slave queue ID: 0

Execute ifconfig -a and check that your bond1 interface is active.

This completes the configuration of LACP bonding on RHEL or CentOS 6 by using the cli tool.

STEPS TO CONFIGURE LACP BONDING ON RHEL OR CENTOS 7 BY USING THE NMCLI TOOL

Backup the existing interfaces that you plan to configure as bond slaves by using the following commands:

~]# ifdown p5p1 ; ifdown p5p2
~]#cd /etc/sysconfig/network-scripts
~]#mv -v ifcfg-p5p1 ifcfg-p5p2 ~/BACKUPDIR

Check the status of the interfaces to be configured as bond slaves by using the following commands:

~]#nmcli con
NAME        UUID                                  TYPE            DEVICE
bond0       f249c64d-724d-416f-aee9-513ad8b6a84b  bond            bond0
em1         20546e2b-a369-4f75-a4f3-0575d48862c3  802-3-ethernet  em1
em2         9a2d2ea6-c865-4f7c-856c-1cc2bbf69449  802-3-ethernet  em2
p5p1        5e377cb8-56ce-4979-882d-4b31a0cdc645  802-3-ethernet  --
p5p2        9cc9a280-295d-4344-be6b-6e69cd1c20b2  802-3-ethernet  --

~]# ethtool p5p1 |grep "Link detected"
Link detected: yes
~]# ethtool p5p2 |grep "Link detected"
Link detected: yes

Create a bond connection by using the bonding options in the preceding preparation table and run the following command for a private network:

~]#nmcli con add type bond con-name bond1 ifname bond1 mode 802.3ad ipv4 179.254.0.2/16
Connection 'bond1' (5a21933b-0c60-4aa6-93b2-b0e4dab6747e) successfully added.

~]#nmcli con mod id bond1 bond.options mode=802.3ad,miimon=100,lacp_rate=fast,xmit_hash_policy=layer2+3
~]#nmcli con mod id bond1 802-3-ethernet.mtu 9000
~]#nmcli con add type bond-slave ifname p5p1 con-name p5p1 master bond1
Connection 'p5p1' (5e377cb8-56ce-4979-882d-4b31a0cdc645) successfully added.

~]#nmcli con add type bond-slave ifname p5p1 con-name p5p2 master bond1
Connection 'p5p2' (9cc9a280-295d-4344-be6b-6e69cd1c20b2) successfully added.

3.5 If you want to setup a bond for public network, you must run the following command instead:

    ~]#nmcli con add type bond con-name bond1 ifname bond1 mode 802.3ad ipv4 179.254.0.2/16 gw <your_gateway>

Restart the NetworkManager service by using the following command:
```
~]#systemctl restart NetworkManager
```

Check the status of the bond and slave interfaces to verify that the bond1 interface is running by using the following commands:

~]#nmcli con
NAME        UUID                                  TYPE            DEVICE
bond0       f249c64d-724d-416f-aee9-513ad8b6a84b  bond            bond0
em1         20546e2b-a369-4f75-a4f3-0575d48862c3  802-3-ethernet  em1
em2         9a2d2ea6-c865-4f7c-856c-1cc2bbf69449  802-3-ethernet  em2
p5p1        5e377cb8-56ce-4979-882d-4b31a0cdc645  802-3-ethernet  p5p1
p5p2        9cc9a280-295d-4344-be6b-6e69cd1c20b2  802-3-ethernet  p5p2
bond1       5a21933b-0c60-4aa6-93b2-b0e4dab6747e  bond            --

~]# nmcli con up uuid 5a21933b-0c60-4aa6-93b2-b0e4dab6747e
Connection successfully activated (master waiting for slaves) (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/8)

~]#nmcli con
NAME        UUID                                  TYPE            DEVICE
bond0       f249c64d-724d-416f-aee9-513ad8b6a84b  bond            bond0
bond1       5a21933b-0c60-4aa6-93b2-b0e4dab6747e  bond            bond1
em1         20546e2b-a369-4f75-a4f3-0575d48862c3  802-3-ethernet  em1
em2         9a2d2ea6-c865-4f7c-856c-1cc2bbf69449  802-3-ethernet  em2
p5p1        5e377cb8-56ce-4979-882d-4b31a0cdc645  802-3-ethernet  p5p1
p5p2        9cc9a280-295d-4344-be6b-6e69cd1c20b2  802-3-ethernet  p5p2

After the configuration is complete, check the output of the following commands to verify that the bond1 interface is active and no error is found:

~]#cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
.
.
.
Output truncated

~]#cat /sys/class/net/bond1/bonding/mode
802.3ad 4

~]# ip a s
.
.
.
6: p5p1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 9000 qdisc mq master bond1 portid 3cfdfe240520 state UP qlen 1000
    link/ether 3e:fc:fb:24:06:30 brd ff:ff:ff:ff:ff:ff
7: p5p2: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 9000 qdisc mq master bond1 portid 3cfdfe240522 state UP qlen 1000
    link/ether 3e:fc:fb:24:06:30 brd ff:ff:ff:ff:ff:ff
9: bond1: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 9000 qdisc noqueue state UP qlen 1000
    link/ether 3e:fc:fb:24:06:30 brd ff:ff:ff:ff:ff:ff
    inet 179.254.0.2/16 brd 169.254.255.255 scope link bond1

This completes the process of LACP bonding on RHEL or CentOS 7 by using the nmcli tool.

Conclusion:

If you need more bandwidth in your network than a single NIC can provide, LACP bonding is very useful. Using IEEE 802.3ad link aggregation in this situation provides increased port density and bandwidth. For more options, refer to the nmcli documentation.

MIkrotik Academy for Network knowledge share

Friday, August 16, 2019

LACP bonding and Linux configuration